Box dieline generator

Beta

Pick a construction, enter the inside dimensions and see the dieline at once. Confirmed, derived and unknown data are marked separately.

Beta tool: check the drawing before production

This tool is in Beta.
Only the listed constructions and their documented ranges are supported.
Before production, check the dimensions, allowances, glue flap, cut and crease lines, and compatibility with your production process.
An automatically generated drawing does not replace a production check.

Supported: FEFCO 0201 — compared with three ArtiosCAD exports (base, L 600, D 450), you set the production values. L, W and D are inside dimensions, in millimeters.

Constructions

Only these constructions are supported; others are added once their geometry is verified.

Box dimensions

Length L (inside)mmRange: 1–2000 mm

Width W (inside)mmRange: 1–2000 mm

Height D (inside)mmRange: 1–2000 mm

Construction options

Panel sequence

Production parameters (not standard)

Set by the producer. Defaults are starting values, not a norm.

Allowance, panel 1 (P1)mmRange: -100–100 mmA production value. In the CAD template it depends on board caliper and settings not available here. The starting value is from the reference.

Allowance, panel 2 (P2)mmRange: -100–100 mmA production value. In the CAD template it depends on board caliper and settings not available here. The starting value is from the reference.

Allowance, panel 3 (P3)mmRange: -100–100 mmA production value. In the CAD template it depends on board caliper and settings not available here. The starting value is from the reference.

Allowance, panel 4 (P4)mmRange: -100–100 mmA production value. In the CAD template it depends on board caliper and settings not available here. The starting value is from the reference.

Height allowance (DZ)mmRange: -100–100 mmA production value. In the CAD template it depends on board caliper and settings not available here. The starting value is from the reference.

Glue flap GmmRange: 1–200 mmIn the CAD template it depends on board caliper; here it is set by hand. The starting value is from the reference.

Slot half-width XmmRange: 0.1–100 mmFrom the fold line to the flap edge: the slot is 2X wide. A production value; the starting value is from the reference.

Slot offset OSmmRange: 0–500 mmHow far the slot reaches past the flap fold line (0 = to the line). Vertical folds are 2·OS shorter.

Glue-flap chamfer angle°Range: 0–60 °A production value. In the CAD template it depends on board caliper and settings not available here. The starting value is from the reference.

Straight stub at the foldmmRange: 0.1–100 mmA production value. In the CAD template it depends on board caliper and settings not available here. The starting value is from the reference.

FEFCO 0201 · Partial

Matches one CAD reference (1849 × 808 mm) for its configuration. You set the production values; other template options are not implemented.

The export is marked “partial geometry”: only the stated ranges are confirmed.

100%

Mouse wheel or + / − to zoom; drag or arrow keys to pan; 0 to reset the view.

Dimensions are computed from the model.

Matches one CAD reference (outline and folds, to 0.001 mm) for its configuration. Other values, rounded or tapered slots, the die-cut machine and other glue joints are not implemented or compared.

Values

Blank width: 1849 mm · derived
Blank height: 808 mm · derived
Flap depth: 202 mm · derived
Body height: 404 mm · derived
Glue flap: 35 mm · derived
Slot width (2X): 8 mm · derived

“Derived” follows from your parameters under the construction's definition, with no reference comparison.

Export

The file carries a note on the geometry status (document title and a line under the dieline).

Download dieline

Vector at physical scale, mm.

PNG resolutionPNG: 4096×1815 px

PNG is a raster made from the vector.

The dieline is large: the PNG is limited to 4096 px on its longer side, so it is not at the chosen resolution. Use PDF or SVG for exact sizes.